H19-404_V1.0 HCSE-Presales-Campus Network Planning and Design V1.0 Questions and Answers

The statement is true. The AirEngine 8771-X1T uses dynamic-zoom smart-antenna technology that can adapt its radiation characteristics according to the deployment environment. In omnidirectional mode, the antenna pattern is optimized to provide broad and balanced coverage, making it appropriate for ordinary offices, corridors, classrooms, and other environments where users are distributed over a relatively large area.

In high-density mode, the antenna pattern is adjusted to concentrate radio energy more effectively within the intended service area. This reduces unnecessary signal leakage, limits interference between neighboring APs, and improves concurrent-user performance in lecture halls, conference rooms, auditoriums, and similar high-density environments.

The switching capability is more effective than using a permanently fixed antenna pattern because WLAN conditions can change as users move and traffic density increases or decreases. Huawei’s training material states that dynamic-zoom smart antennas dynamically switch between omnidirectional and high-density modes, improving coverage in omnidirectional mode while strengthening the user experience in high-density scenarios. Therefore, option A is correct.

==================

The statement is true. In this three-layer campus design, aggregation switches function as VXLAN edge nodes and distributed gateways, while access switches provide terminal connectivity. Policy association allows the access switches to participate in user admission and policy enforcement without requiring them to support full VXLAN functions.

The access switch collects terminal access information and associates user traffic with the appropriate service or policy. The aggregation switch, acting as the fabric edge and VXLAN tunnel endpoint, performs VXLAN encapsulation, distributed gateway forwarding, and policy-related operations. Huawei specifically states that when aggregation switches operate as edge nodes, access switches do not need to support VXLAN and can cooperate with aggregation switches through policy association. This also permits legacy access switches to be reused.

The design reduces upgrade costs and avoids extending complex overlay configurations to every access device. Huawei’s automated virtual-network deployment model also explicitly includes policy association between the aggregation and access layers, allowing access switches without VXLAN capability to operate as transparent or associated access nodes. Therefore, option A is correct.

==================

All four options are recognized terminal identification methods. MAC OUI examines the first three bytes of a device’s MAC address to determine its manufacturer, although it generally cannot identify the exact model or operating system. DHCP option identification analyzes fields such as DHCP options 12, 55, and 60, which can reveal the hostname, parameter-request list, vendor class, and other terminal characteristics. SNMP query is an active identification method that retrieves device details from relevant MIB objects and is particularly useful for printers, network devices, and other SNMP-capable equipment.

Nmap is also an active scanning method. It analyzes open ports, service responses, protocol behavior, and operating-system fingerprints to estimate a terminal’s device type and OS. Huawei distinguishes information-reporting methods from proactive scanning methods: MAC OUI and DHCP options generally use information observed in traffic, whereas SNMP and Nmap actively query or scan the endpoint. iMaster NCE-Campus can correlate multiple fingerprints to improve identification accuracy and automatically apply terminal-specific access policies.

==================

Option C is false. The digital-map energy-saving function provides network-wide energy visibility, identifies periods of low wireless demand, and recommends appropriate energy-saving time windows. During an approved energy-saving period, selected wireless APs or radio resources can be placed into an energy-saving state after the system evaluates coverage, traffic, and capacity requirements.

Automatically powering off switches is not the intended function. Campus switches may carry essential wired services, provide uplinks for other network devices, and supply PoE power to APs, cameras, phones, sensors, and access-control systems. Automatically shutting down a complete switch could therefore interrupt many unrelated services and potentially disconnect downstream network segments.

Huawei identifies low-carbon and energy-saving operation as a characteristic of cloud campus networks and combines this objective with AI-based intelligent O & M and proactive optimization. Its intelligent O & M architecture analyzes AP load trends and performs predictive wireless-network optimization, providing the analytical foundation for selecting safe energy-saving periods and resources.

Therefore, A, B, and D describe supported digital-map energy-saving capabilities. Automatic switch power-off is the false statement, making C correct.

Huawei SD-WAN supports full-mesh, hub-spoke, and partial-mesh interconnection models. In a full-mesh topology, every site can communicate directly with the other sites. This model minimizes intermediate forwarding and is appropriate when branches frequently exchange latency-sensitive traffic such as voice, video, or collaborative application data.

In a hub-spoke topology, branch sites communicate with a central headquarters or data-center hub. Branch-to-branch traffic normally traverses that hub. The model is simple, scalable, and suitable for enterprises whose applications and shared resources are concentrated at headquarters.

Partial-mesh is used when most sites can communicate directly but some sites lack direct underlay connectivity or do not require direct tunnels. Those sites can communicate through a redirect or intermediate site. Huawei describes full-mesh, hub-spoke, and partial-mesh as supported topology designs and explains the role of a redirect site in partial-mesh networking.

“Partial-spoke” is not a defined SD-WAN topology model. A spoke is a role within hub-spoke networking rather than an independent partial-spoke topology. Therefore, A, B, and D are correct.

==================

The distinguishing function supported by the AR6177 is VDSL. VDSL, or Very-high-bit-rate Digital Subscriber Line, enables a branch router to obtain WAN connectivity over existing copper telephone infrastructure. It is appropriate for small branches and distributed sites where Ethernet private lines, fiber, or mobile connections are unavailable or commercially impractical.

The AR6177 can terminate the VDSL access circuit and provide routing, NAT, DHCP, VPN, and other branch-gateway functions for the connected LAN. In this single-answer question, Wi-Fi and PoE are not the defining integrated capabilities of the AR6177 model. Similarly, the complete combination of IPS, antivirus, and URL filtering belongs to a security-enhanced product profile rather than the function used to distinguish the AR6177.

Huawei’s campus design material recognizes DSL links as a specific WAN-access category and notes that deployments involving complex or low-speed links, including DSL, may require an appropriate branch-device deployment method. The model is therefore selected when direct VDSL-based WAN access is required. Consequently, VDSL is the supported capability intended by this question, and option C is correct.

==================

For the R024C10 software release specified in the question, the AR6700V-L cannot be deployed on Google Cloud Platform. The supported environments represented by this release and question are Amazon Web Services, Oracle Cloud, and Microsoft Azure.

Public-cloud support for a virtual CPE is release-specific. A virtual router requires more than generic virtual-machine compatibility. Huawei must provide or validate the appropriate cloud image, virtual network-interface drivers, deployment template, bootstrap mechanism, licensing integration, resource specifications, and controller-registration process for each cloud platform. Therefore, support for one KVM- or VMware-based environment does not automatically mean that every public-cloud provider is supported.

A cloud-hosted virtual CPE enables branches to establish overlay connectivity directly with cloud workloads and allows the controller to provide unified management and policy orchestration for physical and virtual edge devices. Huawei describes this model as deploying a virtual SD-WAN router on a public cloud to implement branch-to-cloud interconnection and unified policy orchestration. Under the R024C10 compatibility matrix tested by this question, GCP is excluded. Therefore, option B is correct.

==================

APs support barcode scanning through the CloudCampus APP, DHCP Option 148–based deployment, and deployment through Huawei’s registration query center. With barcode scanning, the installer scans the AP’s label using the CloudCampus APP. The application obtains information such as the electronic serial number and MAC address, associates the AP with the correct tenant and site, and allows the AP to register with iMaster NCE.

With DHCP Option 148, the DHCP server supplies the AP with its IP configuration and the IP address and port number of iMaster NCE. The AP changes to cloud-management mode and automatically initiates registration. Huawei lists AR routers, switches, and APs as supported devices for this mode.

The registration query center can also provide the controller address after the AP contacts Huawei’s query service. It supports APs together with ARs, firewalls, and switches. Email-based deployment is primarily an SD-WAN CPE or AR-router ZTP method, not an AP deployment mode. Therefore, A, C, and D are correct.

==================

An industrial RedBox can provide all four listed interconnection modes. In HSR-SAN mode, it connects a singly attached node that does not natively support High-availability Seamless Redundancy to an HSR network. The RedBox duplicates frames entering the HSR domain and removes duplicate frames before delivering traffic to the SAN.

HSR-PRP mode interconnects an HSR ring with a Parallel Redundancy Protocol network while preserving seamless redundancy. PRP-PRP mode couples two PRP network domains, while HSR-HSR mode connects separate HSR rings. Depending on the implementation, the HSR-HSR interconnection function may also be described as a QuadBox function because four HSR-facing ports can be involved.

The essential RedBox responsibilities are frame conversion, duplication, duplicate elimination, sequence-number handling, and prevention of unintended forwarding loops between redundancy domains. HSR and PRP use compatible duplicate-identification principles, enabling controlled interconnection between these network types without introducing a single point of failure. RedBoxes also provide redundant connectivity for devices that have only one ordinary Ethernet interface.

==================

A high-density 400GE service card for the CloudEngine S16700 series can provide 18 ports. The S16700 is positioned as a next-generation flagship campus core switch designed for ultra-high-capacity aggregation, large-scale Wi-Fi backhaul, data-center interconnection, and long-term bandwidth evolution.

An 18-port 400GE card provides a theoretical aggregate port rate of 7.2 Tbit/s in each direction before considering the switching fabric’s internal architecture and forwarding design. This density allows a single chassis slot to aggregate numerous high-speed distribution switches, connect multiple campus fabrics, or provide high-bandwidth links toward data centers and service platforms. It also reduces the number of cards and chassis required compared with lower-density 8-port, 12-port, or 16-port alternatives.

The question asks specifically for the number of physical 400GE interfaces offered by the card, not the entire chassis capacity or the number of ports after breakout. Under the H19-404 product-portfolio specification represented by this question, the correct density is 18 native 400GE ports. Therefore, option B is correct.

==================

The statement is true as a WLAN design recommendation. Inter-WAC roaming is supported, but it introduces more control-plane interaction and forwarding complexity than intra-WAC roaming. The Home WAC and Foreign WAC must belong to the same mobility group, synchronize station and AP information, and establish an inter-WAC CAPWAP tunnel for control information and, in some scenarios, service forwarding.

Additional synchronization, tunnel processing, route handling, and failure dependencies can increase roaming delay and complicate troubleshooting. This is especially relevant for delay-sensitive applications such as voice, video, automated guided vehicles, and real-time production systems. A better design places APs between which users frequently move under the same WAC wherever controller capacity and physical topology permit.

Avoiding inter-WAC roaming does not mean disabling the function entirely. Large campuses may require multiple WACs for scale, redundancy, or geographic distribution. Mobility groups should still be configured for unavoidable cross-controller movement. However, buildings, floors, and continuous roaming areas should be assigned carefully so that normal roaming remains intra-WAC. Therefore, the recommendation in the statement is correct, and the answer is True.

==================

The Network Management System is not an element of the IFIT measurement model. An IFIT measurement definition identifies the traffic to be measured, the locations where measurement actions occur, and the direction in which the flow is evaluated. The measurement flow specifies the target packets, usually through flow-identification fields. Measurement points define where packets are marked, counted, timestamped, or reported, such as ingress, transit, and egress nodes. Measurement direction distinguishes forward and reverse monitoring so that packet loss, delay, and path behavior can be analyzed correctly for each direction.

An NMS or controller remains operationally important because it creates measurement tasks, distributes configurations, receives telemetry data, correlates the results, and presents fault-location information. However, it is the management and analysis system surrounding the measurement model, not one of the model’s constituent measurement parameters.

Huawei positions IFIT as a high-precision telemetry mechanism used to delimit and locate application-quality faults. The training material highlights IFIT’s capability to locate faults rapidly and detect packet loss with extremely high reliability. Therefore, the component that is not part of the measurement model is the NMS.

==================

Option C is false. Traditional QoS can classify traffic and provide differentiated treatment for service categories such as voice, video, and ordinary data. It normally performs classification, marking, policing, shaping, congestion avoidance, and queue scheduling on an interface. This provides service-level differentiation but does not deliver sufficiently refined simultaneous management across multiple users and multiple applications.

Huawei’s material explicitly states that traditional QoS schedules traffic based on port bandwidth and can differentiate traffic according to service levels, but it is difficult to distinguish traffic by user. It also states that traditional QoS cannot manage and schedule traffic from multiple services and multiple users simultaneously.

HQoS addresses this limitation through hierarchical, multi-level queues. For example, a parent level can allocate bandwidth to departments, VPNs, sites, or users, while child queues prioritize applications such as voice, video, email, and best-effort traffic. Huawei describes HQoS as hierarchical scheduling that differentiates both services and users. Therefore, statements A, B, and D are correct, while statement C incorrectly attributes an HQoS capability to traditional QoS.

==================

Huawei firewalls provide four commonly predefined security zones: Local, Trust, DMZ, and Untrust. The Local zone represents the firewall itself, including traffic generated by or destined for the device, and has the highest default security priority of 100. The Trust zone normally represents an organization’s protected internal network and has a default priority of 85, not 95. Therefore, option C is false.

The DMZ typically hosts public-facing or semi-trusted resources, such as web, email, and application servers. Its default priority is 50, placing it between the trusted internal network and the external untrusted network. The Untrust zone normally represents the Internet or another uncontrolled network and has the lowest predefined priority of 5.

Zone priority expresses the relative security level used to classify inbound and outbound traffic direction; it does not independently permit traffic. Security policies still determine whether matched traffic is allowed or denied. Huawei’s SD-WAN design uses Trust and Untrust zones on CPEs, and iMaster NCE can orchestrate the corresponding zones and firewall policies for Internet-access protection.

==================

An AP’s transmit power must be maintained within an appropriate range. Excessive power does not automatically improve service quality. A high-power AP can enlarge its interference domain, create co-channel or adjacent-channel interference, produce asymmetric uplink and downlink coverage, and cause sticky-client behavior because a station continues hearing an AP even when its weaker transmission cannot reliably reach that AP. Huawei states that high-power APs can interfere with adjacent APs and that radio calibration dynamically adjusts AP channels, power, and frequency bands to ensure coverage while minimizing interference.

Conversely, power that is too low creates coverage holes, weak received signal strength, low modulation rates, retransmissions, and roaming instability. When a new AP is added, neighboring APs may reduce their transmit power to limit interference. When an AP goes offline, neighboring APs may increase power to compensate for the missing coverage. The engineering objective is therefore neither maximum nor minimum power, but sufficient coverage with controlled overlap and minimum interference. Accordingly, option B is correct.

==================