Weekend Special Limited Time 65% Discount Offer - Ends in 0d 00h 00m 00s - Coupon code: netbudy65

CTS-I Certified Technology Specialist – Installation Questions and Answers

Questions 4

_____ are required when multiple video sources must be displayed on different video displays, or in different zones.

Options:

A.

HDMI repeaters

B.

Looping schemes

C.

Thunderbolt adapters

D.

Matrix routing switchers

Buy Now
Questions 5

The point at which power enters a building is called the _____.

Options:

A.

service entrance

B.

hot spot

C.

facility drop

D.

demark

Buy Now
Questions 6

Why is equipment grounded or wired to the earth?

Options:

A.

to comply with energy conservation regulations

B.

to limit human exposure to high-voltage electricity

C.

to direct excess voltage along the paths of least resistance

D.

to secure equipment in the event of a natural disaster

Buy Now
Questions 7

Perceived illumination decreases by _____ when the distance from a light source is doubled.

Options:

A.

75%

B.

95%

C.

50%

D.

25%

Buy Now
Questions 8

What is a benefit of using the verification standard for system closeout? (Choose all that apply.)

Options:

A.

It aligns outcome and performance expectations at an early stage in the project.

B.

It reduces project risk through early identification of problems, thereby reducing the likelihood of remedial work.

C.

It provides a verifiable outcome.

D.

It creates a common language between all parties.

Buy Now
Questions 9

Half the wraps on one side, twice the wraps on the next side, this is an example of a:

Options:

A.

1:1 Transformer

B.

1:2 Transformer

C.

2:1 Transformer

D.

1:4 Transformer

Buy Now
Questions 10

Compressors, limiters, and expanders are all _____.

Options:

A.

dynamic processors

B.

gates

C.

filters

D.

distortion processors

Buy Now
Questions 11

What does an elevation flag on a plan drawing indicate?

Options:

A.

An interior view of a wall structure

B.

Related elevation drawings

C.

Detailed view of the elevator or lift

D.

Loudspeaker mounting details

Buy Now
Questions 12

How much pulling tension would a 24 AWG microphone cable with a 24 AWG signal cable shield drain wire be able to sustain?

Options:

A.

8.2 kilograms (18 pounds)

B.

5.4 kilograms (12 pounds)

C.

10.9 kilograms (24 pounds)

D.

7.2 kilograms (16 pounds)

Buy Now
Questions 13

In an electrical power distribution installation, the safety earth/ground connects to: (Choose all that apply.)

Options:

A.

the ground (planet Earth)

B.

raceways, ducts, conduit, and cable trays

C.

exposed conductive parts of the installation

D.

equipment racks

Buy Now
Questions 14

Which of the following is true for grouping cables together?

Options:

A.

Keep your signal cables as close as possible to sources of electrical noise

B.

Separate microphone and speaker cables into different bundles

C.

Use nonmetallic conduit for signal cables when nonmetallic conduit is used for power cables

D.

Signal cables should be routed with power cables

Buy Now
Questions 15

A technician installs a condenser microphone. It is not picking up audio. What is the MOST LIKELY cause?

Options:

A.

Pins 2 and 3 are swapped at the XLR connector

B.

The cable run is too long

C.

Phantom power is turned off

D.

The microphone is defective

Buy Now
Questions 16

RGBS requires _____ cables to carry the signal.

Options:

A.

three

B.

two

C.

five

D.

Four

Buy Now
Questions 17

If there are _____ markings on the head of a bolt, it is a Grade 8 ASTM.

Options:

A.

Two

B.

Three

C.

Five

D.

Six

Buy Now
Questions 18

The number of times per second a display will draw the image sent to it is the:

Options:

A.

Frame rate

B.

Refresh rate

C.

Signal-to-noise ratio

D.

Aspect ratio

Buy Now
Questions 19

If a fuse blows and you suspect there is a problem with high-voltage (AC mains) wiring, who should you contact immediately?

Options:

A.

Video engineer

B.

Licensed electrician

C.

Manufacturer's rep

D.

Design consultant

Buy Now
Questions 20

A mirror mounting system must be ____.

Options:

A.

rigid once in place and adjustable during installation

B.

electrically connected to the technical ground

C.

angled so that the mirror reflects the image into the screen twice

D.

electronically adjusted by the control system

Buy Now
Questions 21

The different distributions of white light sources means that each white light_____.

Options:

A.

is exactly the same

B.

has a different tint

C.

illuminates the same way

D.

is perceived in different ways

Buy Now
Questions 22

Which statement accurately describes what you should do when de-installing existing equipment?

Options:

A.

Dispose of equipment right away

B.

Remove the connecting cables

C.

Smash the hardware so that data cannot be stolen

D.

Call an electronic waste recycling contractor

Buy Now
Questions 23

When plotting a cable route, where should you place the cable?

Options:

A.

Close to fluorescent lighting

B.

Away from EMI sources

C.

Near motors or fans

D.

Along complicated pathways

Buy Now
Questions 24

What type of drill bit should you use when drilling a pilot hole into plastic?

Options:

A.

Self-taping screws

B.

A sheet metal bit

C.

A masonry drill bit

D.

A high-speed metal drill bit designed for wood

Buy Now
Questions 25

Numerous, persistent reflections of sound are called _____.

Options:

A.

directional sound

B.

surface reflection

C.

reverberation

D.

echo

Buy Now
Questions 26

Your client has asked you to mount a consumer media and gaming console in the rack. The device measures 340 × 80 x 265 millimeters (W × H × D) (13.4 x 3.1 x 10.4 inches). How many RUs of rack space will this device require?

Options:

A.

1 RU

B.

2 RUs

C.

6 RUs

D.

8 RUs

Buy Now
Questions 27

Crossover cables are used to connect:

Options:

A.

digital and analog devices

B.

devices configured to accept different Data Link layer protocols

C.

two devices without the use of an electronic crossover device

D.

a device's NIC to its MAC address

Buy Now
Questions 28

You have a cable with a part number "RGB5C-25-CM." What is the wire gauge of this cable?

Options:

A.

25 AWG

B.

5 AWG

C.

25 cm

D.

250 AWG

Buy Now
Questions 29

The ___ of a screen should be the same aspect ratio as the projected image.

Options:

A.

shape

B.

size

C.

keystone

D.

height

Buy Now
Questions 30

The second conductor of an unbalanced circuit _____.

Options:

A.

is a shield around the wire used as the electrical circuit's return path

B.

is an insulated wire which transports the signal

C.

has the same impedance as the first signal conductor

D.

carries an inverse image of the first signal conductor

Buy Now
Questions 31

Equipment grounding involves ____.

Options:

A.

disconnecting ground pins to prevent noise

B.

making certain that noise does not flow on signal conductors

C.

tying all conductors to ground

D.

connecting metal conduits, boxes, cabinets, and enclosures to ground

Buy Now
Questions 32

What is the first step in conducting a technical site survey?

Options:

A.

Reviewing drawings with the AV designer

B.

Recording model and serial numbers of all equipment

C.

Setting up your GPS with the site location

D.

Ordering the equipment from the warehouse

Buy Now
Questions 33

In a _____ loudspeaker circuit, you will connect a positive wire from an amplifier to another positive wire on each of the loudspeakers in the circuit.

Options:

A.

Parallel

B.

Series

Buy Now
Questions 34

When should you run electrical and signal cables to a flat panel display?

Options:

A.

Before you've found all of the studs behind the mounting wall

B.

After you've made final adjustments to the display based on the viewing environment

C.

Once you've placed it upon a flat, clean, shipping blanket

D.

After it's been mounted to the wall

Buy Now
Questions 35

The conversion of energy from one form to another is called _________.

Options:

A.

Transduction

B.

Frequency

C.

Propagation

D.

Amplification

Buy Now
Questions 36

The ISO numerical marking scheme on materials is used to:

Options:

A.

indicate the strength of the material the hardware is made from

B.

calculate the length of the hardware

C.

test the amount of impurities present in the material the hardware is made from

D.

calculate the weight of the material the hardware is made from

Buy Now
Questions 37

What kind of material might be used in some rear projection screen applications?

Options:

A.

diffused

B.

high-gloss

C.

reflective

D.

opaque

Buy Now
Questions 38

When a live microphone is placed too close to a loudspeaker, ____ will occur.

Options:

A.

feedback

B.

buzzing

C.

static

D.

Amplification

Buy Now
Questions 39

On which type of cable should you avoid using cable lubricants?

Options:

A.

CAT5e cable

B.

Shielded cable

C.

Fiber optic cable

D.

Coaxial cable

Buy Now
Questions 40

Rear screen display applications are considered _____.

Options:

A.

remissive

B.

emissive

C.

transmissive

D.

Reflective

Buy Now
Questions 41

Exceeding the pulling tension can stretch a cable and change its _____.

Options:

A.

plenum rating

B.

electrical properties

C.

bend radius

D.

length

Buy Now
Questions 42

Which part of the eye enables people to see at night?

Options:

A.

retina

B.

cones

C.

rods

D.

Iris

Buy Now
Questions 43

Flexible PVC rear projection screens:

Options:

A.

can be easily punctured, attract dirt easily and must be stretched firmly when installed.

B.

are best used in manual wall projection setups

C.

are the screen type most resistant to wrinkles, scratches, and punctures.

D.

must be stretched flat, which is easily done on the floor before installation, for optimal image clarity.

Buy Now
Questions 44

What are the five stages of the typical AV process lifecycle?

Options:

A.

Programming, executing, planning, installing, closing

B.

Programming, designing, installing, commissioning, training

C.

Designing, installing, planning, commissioning, training

D.

Initiating, planning, executing, control, closing

Buy Now
Questions 45

Conduit fill percentage varies by the ___.

Options:

A.

Number of cables

B.

Quality of cables

C.

Gauge of cables

D.

Length of cables

Buy Now
Questions 46

____ isolates and protects a signal from sources of electromagnetic and radio frequency interference.

Options:

A.

Shielding

B.

Coaxial Cabling

C.

A transformer

D.

Noise

Buy Now
Questions 47

During a technical site survey for an installation with a display, information gathered should include:

Options:

A.

Color of the walls

B.

Receptionist name and phone number

C.

Ceiling height and construction method

D.

Rules governing use of the freight elevator

Buy Now
Questions 48

The number of ___ in the primary and secondary sides of a transformer determines the impedance and/or voltage ratio.

Options:

A.

Unused tap wires

B.

Ohms

C.

Coils of wire

D.

Loudspeaker taps

Buy Now
Questions 49

Typically, what type of connector finishes the shielded twisted pair cable?

Options:

A.

USB

B.

XLR

C.

RJ-45

D.

TRS

Buy Now
Questions 50

A high pass filter is typically used during equalization for ___.

Options:

A.

Eliminating potential hissing sounds in the system.

B.

Removing rumble from an HVAC system.

C.

Adding emphasis to the lower frequency range.

D.

Adding hum to the system.

Buy Now
Questions 51

What Viewing Category applies to a space used for medical imagery?

Options:

A.

ADM

B.

BDM

C.

Both ADM and BDM

Buy Now
Questions 52

To find the aspect ratio of a screen, you must _____.

Options:

A.

divide the screen width by the screen length

B.

multiply the aspect ratio by the screen height

C.

substitute the width or height in the formula

D.

divide the screen width by the screen height

Buy Now
Questions 53

In the professional AV industry, the most common direct view displays are _____.

Options:

A.

video walls

B.

televisions

C.

monitors

D.

projection systems

Buy Now
Questions 54

When planning an electrical system, do not exceed ____ of the capacity of any circuit.

Options:

A.

80%

B.

95%

C.

75%

D.

65%

Buy Now
Questions 55

The published design weight of a speaker array with mounting hardware totals 96 kilograms (212 pounds). What minimum weight should the substructure and mounting assembly be able to support?

Options:

A.

227 kilograms (500 pounds)

B.

962 kilograms (2,120 pounds)

C.

480 kilograms (1,060 pounds)

D.

192 kilograms (424 pounds)

Buy Now
Questions 56

Different colors of light vary in __________.

Options:

A.

Wavelength

B.

Proportion

C.

Chromaticity

D.

Intensity

Buy Now
Questions 57

A reference microphone for setting equalization of a speaker system should: (Choose all that apply.)

Options:

A.

be the same brand and type used in the system as designed

B.

be omnidirectional

C.

have a flat, on-axis response

D.

have a nonreflective surface

Buy Now
Questions 58

What is the industry best practice when troubleshooting? (Choose all that apply.)

Options:

A.

Change only one thing at a time

B.

Change the faulty device right away

C.

Change the signal analyzer

D.

Change the signal generator

Buy Now
Questions 59

In the event of a change in the placement of air-conditioning ducts in a boardroom, which of the following documents should the AV integrator submit first?

Options:

A.

Punch/snag/problem list

B.

Change order (CO)

C.

Request for change (RFC)

D.

Request for information (RFI)

Buy Now
Questions 60

A _____ is a long flexible tape used to pull cable through conduit.

Options:

A.

Snout

B.

Tape measure

C.

Mouse

D.

Fish tape

Buy Now
Questions 61

What type of rack would you use for a room with limited space for servicing equipment?

Options:

A.

Fixed stand-alone

B.

Portable

C.

Wall-mounted

D.

Slide out

Buy Now
Questions 62

Bandwidth ____ as the resolution of an image increases.

Options:

A.

increases

B.

fluctuates

C.

remains the same

D.

Decreases

Buy Now
Questions 63

Visual Acuity is __________.

Options:

A.

the visual angle of 1 minute of arc

B.

the ability to perceive and assimilate visual information

C.

an optotype

D.

20/20 vision

Buy Now
Questions 64

When working with electrical systems, what should you do if two codes have conflicting requirements?

Options:

A.

Follow the guidelines from the most restrictive code

B.

Follow the guidelines from the most lenient code

C.

Consult the NEC handbook and do only what it says

D.

Ignore both of the codes and do the installation in a way that makes sense to you

Buy Now
Questions 65

Items which require user control should be placed in the _____ of the rack.

Options:

A.

very top

B.

middle

C.

back

D.

Bottom

Buy Now
Questions 66

Which are best practice methods for dressing a rack? (Choose all that apply.)

Options:

A.

Bundle cables by signal type.

B.

Use removable cable ties to secure a cable bundle.

C.

Secure heavy cable bundles to lacing bars.

D.

Keep power cables separate from signal cables.

Buy Now
Questions 67

When mounting a projector to the ceiling, one must identify the center point location of the mounting assembly, because:

Options:

A.

This is the point where the projector's weight is evenly distributed over the entire mounting plate.

B.

This is where the adjustable mount support structure must be centered.

C.

This is the center point of the projector's lens.

D.

This is the projection throw distance calculation reference point.

Buy Now
Questions 68

DISCAS addresses the following viewing categories:

Options:

A.

Passive Viewing

B.

Basic Decision Making

C.

Analytical Decision Making

D.

Full Motion Video

Buy Now
Questions 69

When demonstrating the operation of a digital visual system with multiple connections for laptops, it is recommended to:

Options:

A.

Connect the laptops to confirm that they will properly display the resolution set by the EDID table

B.

Use a video test pattern generator to test all laptop connections

C.

Describe the different resolutions that the system is capable of displaying

D.

Utilize a real time generator to confirm that the system will output the proper resolution set by the EDID table

Buy Now
Questions 70

What type of drawing view shows the layout of items on the ceiling?

Options:

A.

Reflected ceiling plan

B.

Reflected floor plan

C.

Detail ceiling drawing

D.

Elevation drawing

Buy Now
Questions 71

According to InfoComm best practices, why should you use pre-measured bolts when connecting a mounting bracket to a flat panel display?

Options:

A.

Bolts that are not pre-measured may pose a security risk

B.

Bolts that are too short will not secure the display

C.

Bolts that are too long can damage the mounting bracket

D.

Bolts that are too short can damage the wall

Buy Now
Questions 72

Which of the following should be included in a Network Device Inventory? (Choose all that apply.)

Options:

A.

Ports used by each device

B.

Device model numbers and firmware versions

C.

Physical dimensions of each device

D.

MAC address of each device

Buy Now
Questions 73

What CLI command would you use to discover the IP address of a device you are currently using?

Options:

A.

ping

B.

ipconfig

C.

arp

D.

loopback

Buy Now
Questions 74

Once an audio signal has left a microphone, what processor will it encounter first?

Options:

A.

The audio mixer

B.

Acoustic echo cancellation

C.

The power amplifier

D.

The preamplifier

Buy Now
Questions 75

What type of termination technique is used for a solid conductor RJ45 connector?

Options:

A.

Solder

B.

Crimp

C.

Insulation displacement

D.

Compression

Buy Now
Questions 76

What will keep the tile from sagging after the loudspeaker is installed?

Options:

A.

Back box

B.

Tile Bridge

C.

Grille

D.

Tile can

Buy Now
Questions 77

Determine the wattage in a circuit measuring 120 volts with 15 amperes of current flow.

Options:

A.

80W

B.

0.125W

C.

1800W

D.

8W

Buy Now
Questions 78

If the audio digital signal processor you have to install is discontinued by the manufacturer, what should you do? (Select all that apply.)

Options:

A.

Install another similar model and record the model number on the project documentation

B.

Discuss the need for change with the AV designer and your project manager

C.

Redline the change on the appropriate project document, send it to your project manager for submission of a formal RFI or RFC, and wait for a CO

D.

Try to find the specific model through an online vendor

Buy Now
Questions 79

In a BDM environment, viewers are more concerned with __________.

Options:

A.

pixel-level detail than the entire image

B.

overall content than detail

C.

the finest details than overall content

Buy Now
Questions 80

What is the function of a back box?

Options:

A.

It keeps sound contained into a single room

B.

It transmits sound to adjoining areas through the ceiling space

C.

It limits the low frequency response of the loudspeaker

D.

It helps hold the wires stable as you crimp butt splices onto them

Buy Now
Questions 81

If a display has 800 pixels horizontally and 600 pixels vertically, what is its native resolution?

Options:

A.

800x600

B.

1600x1200

C.

1200x1600

D.

600x800

Buy Now
Questions 82

Rear projection is a transmissive system that _____.

Options:

A.

requires little space for installation

B.

allows light to pass through a translucent screen toward the viewer

C.

handles ambient light issues more poorly than front screen projection

D.

can allow a presenter to block all or part of the image

Buy Now
Questions 83

What is the primary reason an AV installer should attend weekly construction meetings?

Options:

A.

Learn about safety requirements

B.

Establish relationships with allied trade teams

C.

Identify changes that will affect the AV installation

D.

Find out when the cafeteria is open

Buy Now
Questions 84

This conduit type forms a lightweight continuous flexible tube that offers the advantage of EMI protection.

Options:

A.

PVC

B.

Thinwall

C.

Rigid

D.

Flex

Buy Now
Questions 85

Which test verifies a signal can travel from one end of the cable to the other?

Options:

A.

Impedance

B.

Continuity

C.

Insulation

D.

Polarity

Buy Now
Questions 86

Project budget refers to which of the following?

Options:

A.

The amount of labor and materials the project manager has allocated to complete the project

B.

The total amount that the client has paid the AV company for the project

C.

The amount needed for purchasing the materials and supplies

D.

The actual cost of labor and materials used to complete the project

Buy Now
Questions 87

In the conduit capacity formula, the two symbols used are ___ diameter of the conduit and ____ diameter of the cable.

Options:

A.

Inner, outer

B.

Outer, inner

C.

Outer, outer

D.

Inner, inner

Buy Now
Questions 88

A projector weighing 195 kilograms (429 pounds) should be mounted only to what type of surface?

Options:

A.

Ceiling tile of an auditorium

B.

Front wall in a classroom

C.

Drywall in conference room

D.

Building structural support or blocking

Buy Now
Questions 89

How can you exceed the recommended 50-foot (15.25 meter) HDMI cable length without having signal loss?

Options:

A.

Use a thunderbolt cable

B.

Use an HDMI coupler

C.

Use an HDMI repeater

D.

Use an active cable

Buy Now
Questions 90

Why is color temperature awareness important in the AV industry?

Options:

A.

"Whiteness" is subjective with ever changing definitions.

B.

People expect exact "whiteness" when viewing a display.

C.

The AV industry strives to set the standard for "whiteness."

D.

AV equipment allows for adjusting the "whiteness" for optimal display.

Buy Now
Questions 91

Cameras installed _________ will capture the side of a participants head while they look at the display in front of them.

Options:

A.

Behind the presenter

B.

Too high up

C.

Too far to the left

D.

Too low down

Buy Now
Questions 92

What should be done with empty cardboard equipment boxes?

Options:

A.

Returned to the manufacturer

B.

Stored in a closet

C.

Discarded in the dumpster/waste container

D.

Discarded where indicated by the client

Buy Now
Questions 93

Which of the following steps should be undertaken before attempting the troubleshooting process? (Choose all that apply.)

Options:

A.

Familiarize yourself with the AV systems and equipment

B.

Have the system documentation at hand

C.

Order a spare system controller

D.

Get an understanding of the warranty and maintenance agreements

Buy Now
Questions 94

How can you determine where the loudspeakers go during a loudspeaker installation?

Options:

A.

Refer to the elevation diagrams from your designers

B.

Refer to the reflected ceiling plans from your designers

C.

They belong in the same tile as fire suppressant sprinklers do

D.

Ask your project manager before installing every single loudspeaker

Buy Now
Questions 95

In a projected image, adding colors makes the image _____.

Options:

A.

dimmer

B.

brighter

C.

sharper

D.

Darker

Buy Now
Questions 96

_____ prevent loud signals from being too loud.

Options:

A.

Compressors

B.

Filters

C.

Limiters

D.

Expanders

Buy Now
Questions 97

Which of the following provides a method of ensuring the best image quality between source and sink/display?

Options:

A.

HDCP

B.

EDID

C.

HDMI

D.

Hot plug

Buy Now
Questions 98

What is a best practice when installing cables where there is no conduit or other raceway for ceiling-mounted projectors?

Options:

A.

Interlacing the cables

B.

Resting the cables gently on the ceiling tile

C.

Stacking the cables along one side of the ceiling grid

D.

Securing the cables with bridle rings mounted to bar joists

Buy Now
Questions 99

_____ signals combine all five video signals on a single cable.

Options:

A.

Component

B.

RGBS

C.

Composite

D.

RGBHV

Buy Now
Questions 100

What is the point at which mains power enters a building?

Options:

A.

The feeder

B.

The main distribution board

C.

The electrical entrance

D.

The main line

Buy Now
Questions 101

Which is the preferred method for the correction of keystone distortion?

Options:

A.

Optical

B.

Electronic

C.

Digital

D.

Analog

Buy Now
Questions 102

_____ is the distance in meters between two corresponding points of two consecutive cycles.

Options:

A.

Magnitude

B.

Amplitude

C.

Frequency

D.

Wavelength

Buy Now
Questions 103

For an ethernet cable (UTP) to meet certification standards, the maximum length is

Options:

A.

98' or 30m

B.

328' or 100m

C.

492' or 150m

D.

984' or 300m

Buy Now
Questions 104

What is a characteristic of multimode fiber optic cables?

Options:

A.

Multimode uses yellow cable jackets

B.

Multimode cables send the signal quicker than single-mode cables

C.

Multimode disperses the signal into many light paths

D.

Multimode cable does not have limited bandwidth

Buy Now
Questions 105

The refractive index varies for different wavelengths of light, producing an effect called _____.

Options:

A.

refraction

B.

reflection

C.

dispersion

D.

Absorption

Buy Now
Questions 106

A "just noticeable" change in sound pressure level, either louder or softer, requires a _____ change.

Options:

A.

+/-10 dB

B.

+/-3 dB

C.

+/-6 dB

D.

+/-1 dB

Buy Now
Questions 107

Which test verifies that a cable can transmit a signal from one end to another?

Options:

A.

Polarity test

B.

Impedance test

C.

Continuity test

D.

Signal sweep test

Buy Now
Questions 108

Which of the following can control systems operate remotely? (Choose all that apply.)

Options:

A.

Power

B.

Drapes/curtains

C.

Display monitors

D.

Lights

Buy Now
Questions 109

What are the methods used to cool an AV equipment rack? (Choose all that apply.)

Options:

A.

Pressurization

B.

Decompression

C.

Refrigeration

D.

Evacuation

Buy Now
Questions 110

What type of termination technique is used for a BNC connector?

Options:

A.

Solder

B.

Crimp

C.

Insulation displacement

D.

Stab and twist

Buy Now
Questions 111

Which set of drawings should you reference to view the ductwork that goes through the building?

Options:

A.

Architectural drawings

B.

Mechanical drawings

C.

System drawings

D.

Electrical drawings

Buy Now
Questions 112

In the AV Industry, _____ (tin/lead) solder is typically used.

Options:

A.

40/60

B.

63/37

C.

50/50

D.

28/72

Buy Now
Questions 113

Which sequence of numbers depicts part of a logarithmic scale?

Options:

A.

1, 2, 3, 5, 8

B.

1, 10, 100, 1000

C.

1, 2, 3, 4

D.

1, 13, 26, 49

Buy Now
Questions 114

What device is needed to calibrate an SPL Meter:

Options:

A.

An SPL Calibrator that produces 94 dB SPL=1Pa

B.

Scaler

C.

Transcoder

D.

EDID emulator

Buy Now
Questions 115

Checking an electrical system for a _____ should only be performed with the aid of a qualified electrician.

Options:

A.

Hot/neutral swap

B.

Open ground-wiring error

C.

Hot/ground swap

D.

Neutral/ground swap

Buy Now
Questions 116

Which of the following is a form of encryption to protect copyrighted content?

Options:

A.

VESA

B.

EDID

C.

HDMI

D.

HDCP

Buy Now
Questions 117

Which of the following is mic-level voltage?

Options:

A.

316 millivolts (-10dBV)

B.

1.23 volts (+4dBu)

C.

Up to about 100 volts

D.

0.3 to 1 millivolts (-60 to -50dBu)

Buy Now
Questions 118

When a transmitter or radio station creates noise in a microphone line, it is called _____.

Options:

A.

EMI

B.

a magnetic field

C.

hum or buzz

D.

RFI

Buy Now
Questions 119

The back light _____.

Options:

A.

fills in dark spots which are created

B.

shines on the subject's shoulders and hair

C.

is the brightest light on the subject

D.

lights the background

Buy Now
Questions 120

How many dimensions does color space possess?

Options:

A.

two

B.

three

C.

five

D.

four

Buy Now
Questions 121

What is inserted between structural building elements to provide a secure mounting point for products?

Options:

A.

Post-tension cables

B.

Grade 5 bolts

C.

Poured pan concrete

D.

Wood blocking

Buy Now
Questions 122

The picture is an example of a:

Options:

A.

Series circuit

B.

AC Circuit

C.

DC Circuit

D.

Parallel Circuit

Buy Now
Questions 123

What assumptions should you make about an audio system when there is no audio output? (Choose all that apply.)

Options:

A.

The gain on the main audio amplifier may be wound down to zero.

B.

The mixing desk channel for the microphone is switched to line input mode.

C.

The user is a complete idiot and did not switch the microphone on.

D.

Make no assumptions at all and select a troubleshooting strategy.

Buy Now
Questions 124

Optical screen material is used in most _____ rear screen applications.

Options:

A.

temporary

B.

permanent

C.

mobile

D.

Stationary

Buy Now
Questions 125

Phantom power is the _____ required to power a condenser microphone.

Options:

A.

polarized conductor

B.

internal capacitor

C.

remote power

D.

electrical field

Buy Now
Questions 126

What kind of facility might use a sound masking system?

Options:

A.

gymnasium

B.

library

C.

hospital

D.

shopping mall

Buy Now
Questions 127

What are the benefits of using the ANSI/AVIXA 10:2013 Standard for Audiovisual Systems Performance Verification? (Choose all that apply.)

Options:

A.

Reducing project risk

B.

Aligning outcome and performance expectations

C.

Providing a verifiable outcome

D.

Creating reporting that completes the project documentation

Buy Now
Questions 128

_____ are the result of a(n) _____ reflection.

Options:

A.

Echoes, early

B.

Wavelengths, diffuse

C.

Diffusions, small

D.

Echoes, late

Buy Now
Questions 129

A rack elevation diagram includes which of the following information?

Options:

A.

Location of electrical outlets for technical power

B.

The distance from the floor the rack should be mounted

C.

Signal type for each input and output

D.

RUs used for each component

Buy Now
Questions 130

A key objective for mounting AV equipment in a rack is to:

Options:

A.

hide it discretely in a closet

B.

protect the integrity of the system

C.

ensure only technical personnel can access it

D.

roll the gear in and out easily

Buy Now
Questions 131

Sound reinforcement systems are used to perform which of the following?

Options:

A.

reinforce the human voices only

B.

separate sound signals

C.

register outgoing sounds

D.

increase the sound distributed over a larger area

Buy Now
Questions 132

Which diagram is used for positioning mounted equipment within a rack?

Options:

A.

A rack building diagram

B.

A rack elevation diagram

C.

A rack mounting diagram

D.

A rack system diagram

Buy Now
Questions 133

What does a low pass filter do?

Options:

A.

removes the low frequency content of a signal

B.

amplifies the low frequency content of a signal

C.

passes the low frequency content of a signal

D.

mutes the low frequency content of a signal

Buy Now
Questions 134

OLEDs are _____ type devices.

Options:

A.

lenticular

B.

transmissive

C.

refractive

D.

Emissive

Buy Now
Questions 135

What Viewing Category applies to a space used for word processing and spreadsheets?

Options:

A.

ADM

B.

BDM

C.

Both ADM and BDM

Buy Now
Questions 136

H and V sync signals are transmitted as separate signals on a(n) _____ output.

Options:

A.

digital

B.

analog

C.

RBG

D.

RS232

Buy Now
Questions 137

Which one of these is an unsafe lift practice?

Options:

A.

Do not bend your knees and do the lifting with your back.

B.

Be sure to keep a firm footing and balance the weight between your feet

C.

Do not perform the lift alone; Always have a partner or helper.

D.

Perform the lift slowly; Do not make sudden movements or rotate during the lift

Buy Now
Questions 138

After which of the following activities is an AV project completed?

Options:

A.

All hardware is installed

B.

Software integration is completed

C.

Verification that the system is operational

D.

System closeout activities are completed

Buy Now
Questions 139

Which of the following is a compiled program?

Options:

A.

Machine code

B.

DVD titles

C.

RAW codec

D.

Control script

Buy Now
Questions 140

SDI signals are usually transported using _____ connectors.

Options:

A.

RCA

B.

BNC

C.

HDMI

D.

DVI-D

Buy Now
Questions 141

When training a customer on the operation of a touch panel interface, an example that the GUI is a good design that meets the customer's needs:

Options:

A.

The customer can easily step in and use the Touch Panel with little explanation

B.

The customer requires intensive training on the operation of the Touch panel

C.

The customer thinks the panel looks cool

D.

The customer wants only a few changes

Buy Now
Questions 142

Which of these are layer 2 protocols commonly used to transport real-time media over a network? (Choose all that apply.)

Options:

A.

Dante

B.

UDP

C.

TCP

D.

AVB

Buy Now
Questions 143

As light increases, _____ kicks in and adjusts until it has closed to its maximum.

Options:

A.

Auto-shutter

B.

Auto gain

C.

Depth-of-field

D.

The auto-iris

Buy Now
Exam Code: CTS-I
Exam Name: Certified Technology Specialist – Installation
Last Update: Sep 11, 2025
Questions: 477

PDF + Testing Engine

$134.99

Testing Engine

$99.99

PDF (Q&A)

$84.99